| SPECIALS FROM VELOCE SPARES | |||
| ELECTRICAL | |||
| 38ET | MILLER REP T/LAMP S/A 6V BULB | £13.49 | |
| H35 | BEARING RETAINING PLATE | £0.55 | |
| H37 | DYNO THRU BOLTS SHORT | £0.55 | |
| H41 | BRUSH SPRING POS/NEG STATE? | State whether for positive or negative | £0.35 |
| H46 | BRASS TERMINAL EXTENSIONS | £0.25 | |
| L564 | LUCAS 564 REP. R/ LIGHT,12V | £13.59 | |
| VSL057 | AMMETER HOLDING STRAP | £1.10 | |
| VSL060 | LUCAS MAG CAP CHROME | £3.30 | |
| VSL065A | K1F PICKUP GASKET | £0.30 | |
| VSL067 | BTH SLIP RING | £9.90 | |
| VSL067A | LUCAS SLIP RING | £9.91 | |
| VSL073 | MILLER REPL. HORN /DIP-SWITCH | £14.70 | |
| VSL076 | MILLER REP.''STOP'' LIGHT,12V | £27.60 | |
| VSL081 | WIRING CABLE | Available: Black, Blue, Brown, Red, Yellow, Green or White - priced per yard | £0.55 |
| VSL083 | GTP CAPACITOR | £2.20 | |
| VSL085 | ATD SPRING MAC 498157 PAIR | £1.35 | |
| VSL086 | ATD SPR VM ETC 422243/S PAIR | £1.35 | |
| VSL087 | BRK LIGHT SWITCH PLATE | £5.00 | |
| VSL088 | 12 V 6 WATT SINGLE CONTACT | £0.35 | |
| VSL089 | BULB 12V 48/48 PRE-FOCUS | £1.00 | |
| VSL089B | BULB 12V 36/36 PRE-FOCUS | Hoping to reorder soon | £1.00 |
| VSL089C | BULB 12V 50/40 PRE-FOCUS | £2.57 | |
| VSL090 | 6V 21/5W SBC BULB R.LIGHT | £0.95 | |
| VSL090A | BULB 6V 30/24 H/LIGHT | £3.18 | |
| VSL090B | 12V 21/5W STOP/TAIL BULB | £0.45 | |
| VSL090D | BULB, 12V, 2.2W, SCREW IN | £0.50 | |
| VSL091 | STOP SWITCH ASSEMBLY & BRACKET | Shrouded Hella switch mounted on a stainless bracket, with spring etc - a direct replacement for the original Miller switch and flat plate - see cover photo (not suitable for use with rearset footrests) | £23.00 |
| VSL092 | RUBBER GASKET MILLER DIPSWITCH | £0.30 | |
| VSL350 | WIRING LOOM LUCAS PLASTIC | £23.76 | |
| VSL351M | WIRING LOOM. ORIG PATT MILLER. | For Miller Dynamo combined with Miller switch, an exact replica of original in a plastic sheath, as were most but not all post-war models. | £25.00 |
| VSL352 | WIRING LOOM COIL PLASTIC | For Coil Ignition system | £22.00 |
| VSL391 | REPLICA MILLER 6 1/2 H/L RIM | Does not include sprung toggle fixing | £15.00 |
| VSL392 | REPLICA MILLER 7 INCH H/L RIM | £15.00 | |
| VSL393 | H LAMP RIM CLIP | Replica in Stainless - complete set of parts for sprung toggle 'wing' clip | £8.25 |
| VSL453 | 1 1/2 INCH REAR REFLECTOR | Chromed bezel - Hoping to reorder soon | £3.40 |
| PISTONS & ASSOCIATED PARTS | |||
| K149 | PISTON CIRCLIP MAC/MOV/KSS | £0.35 | |
| M31/4 | VR GUDGEON PIN | £16.50 | |
| MAS97/19SS | VIPER PISTON STD SPLIT/SKIRT | Original Wellworthy split skirt | £48.50 |
| MAS97/22 | 86MM MSS PISTON STANDARD | Omega | £67.00 |
| MAS97/24/60 | 86MM MSS PISTON PLUS 60 | Omega 0.060" oversize | £67.00 |
| RT27 | PISTONS GTP VARIOUS | £25.00 | |
| VSL118A | KSS MK 2 PIST.RING SEPARATE | Limited stock - state size required in case we can supply | £4.00 |
| VSL118B | PIST RING MOV/MAC SEPARATE | Limited stock - state size required in case we can supply | £4.00 |
| VSL118C | PIST RING VM/MSS SEPARATE | Limited stock - state size required in case we can supply | £4.00 |
| VSL118D | PIST.RING VR SEPARATE | Limited stock - state size required in case we can supply | £4.00 |
| VSL119B | GUDGEON PIN MOV/MAC | £16.50 | |
| VSL121 | PISTON RING SETS MSS 81MM | £17.25 | |
| VSL121A | PISTON RING SETS KSS MK2 | Limited stock - state size required in case we can supply | £17.25 |
| VSL121B | PISTON RINGS MOV/MAC SETS | Limited stock - state size required in case we can supply | £17.25 |
| VSL121D | PISTON RING SET VR | Limited stock - state size required in case we can supply | £17.25 |
| HANDLEBARS & GRIPS | |||
| VSL021 | HANDLEBAR PUSH/PULL THROTTLE | Stainless, Dull finish, requires polish or plate - FK61/4AS equivalent | £38.00 |
| VSL022 | HANDLEBAR MOV/MAC/GTP WEBB | Stainless, bright finish but not polished - FK61/3 equivalent - Hoping to reorder soon | £16.50 |
| VSL025 | HANDLEBAR KSS | Stainless, bright finish but not polished - FK61/6 equivalent | £22.00 |
| VSL026 | HANDLEBAR KTS/RIGID MSS | Stainless, Dull finish, requires polish or plate - FK61/4 equivalent - Hoping to reorder soon | £21.00 |
| VSL030 | HANDLEBAR TELE FORKS STANDARD | Stainless, bright finish but not polished - FK61/8 equivalent for all models with tele forks (including Dowty) - Hoping to reorder soon | £22.00 |
| VSL114 | HANDLE BAR RUBBERS, PLAIN | 6 inch long, fits twistgrip side only | £0.30 |
| CONTROL & DRIVE CABLES | |||
| These control cables replace the Velocette originals for steel blade controls without adjusters. | |||
| If you have non-standard levers, please check that the cable dimensions are suitable before | |||
| attempting to fit them - damaged or modified cables cannot be exchanged or refunded | |||
| VSL122 | FRONT BRAKE MOV/MAC 33-48 | Front brake, Mac/Mov 1933-48 | £16.44 |
| VSL123 | FRONT BRAKE TELES 49-52 | Front brake, Mac telescopic fork 1949-52- please order VSL126 which is equivalent | |
| VSL124 | FRONT BRAKE MSS 35-47 | Front brake, Mss 1935-47 - Hoping to reorder soon | |
| VSL125 | FRONT BRAKE KSS 32-48 | Front brake, Kss 1932-48 | £20.00 |
| VSL126 | FRONT BRAKE ALL S/ARM 53 ON | Front brake, all swing/arm 1953 on | £12.75 |
| VSL127 | FRONT BRAKE VMT HEAVY DUTY | Front brake, Thruxton, heavy duty type | £15.00 |
| VSL128 | CLUTCH RIGID ADJ.UNDER TANK | Clutch, rigids, mid adjuster under petrol tank | £13.00 |
| VSL129 | CLUTCH S/ARM ADJ. UNDER TANK | Clutch, swing/arm, mid adjuster under petrol tank | £9.95 |
| VSL130 | CLUTCH S/A ADJ AT G.BOX | Clutch, swing/arm, adjuster above gearbox | £12.50 |
| VSL131 | MAGNETO BTH | Magneto, advance/retard, BTH ( not competition mag) | £12.50 |
| VSL132 | MAGNETO LUCAS | Magneto, advance/retard, Lucas | £15.00 |
| VSL133 | VALVE LIFTER BARREL NIPPLE | Valve lifter, barrel shaped nipple at handlebar end | £11.25 |
| VSL134 | VALVE LIFTER BALL NIPPLE | Valve lifter, ball shaped nipple at handlebar end | £11.00 |
| VSL135 | THROTTLE 275/6 WITH MID-ADJUST | Throttle, 275/6, mid adjuster, top hat at carb.(1/4" diameter nipple) | £6.75 |
| VSL135A | THROTTLE 275/6 | Throttle, 275/6, adjuster in carb top & also mid adjuster (1/4" diameter nipple) | £9.00 |
| VSL136 | THROTTLE MONOBLOC | Throttle, monobloc, mid adjuster, top hat at carb. (1/4" diameter nipple) | £10.19 |
| VSL136A | THROTTLE MONOBLOC | Throttle, monobloc, mid adjuster, plain ferrule at carb. for adjuster in carb top (1/4" diameter nipple) | £6.00 |
| VSL136B | THROTTLE MONOBLOC | Throttle, monobloc, plain ferrule at carb. for adjuster in carb top (1/4" diameter nipple) - Hoping to reorder soon | £4.50 |
| VSL136C | THROTTLE MONOBLOC | Throttle, monobloc, mid adjuster, top hat at carb. (3/16" diameter nipple) | £7.15 |
| VSL137 | THROTTLE CONCENTRIC | Throttle, concentric, mid adjuster, top hat at carb. (3/16" diameter nipple) | £6.75 |
| VSL137A | THROTTLE CONCENTRIC | Throttle, concentric, mid adjuster, plain ferrule at carb. for adjuster in carb top (3/16" diameter nipple) | £7.15 |
| VSL137B | THROTTLE CONCENTRIC | Throttle, concentric, mid adjuster, top hat at carb. (1/4" diameter nipple) | £9.00 |
| VSL137C | THROTTLE CONCENTRIC | Throttle, concentric, plain ferrule at carb. for adjuster in carb top (1/4" diameter nipple) | £4.25 |
| VSL137D | THROTTLE CONCENTRIC | Throttle, concentric, mid adjuster, plain ferrule at carb. for adjuster in carb top. (1/4" diameter nipple) | £7.15 |
| VSL141 | CHOKE ALL CARBS MID-ADJ | Choke, all, mid adjuster, top hat at carb. | £10.00 |
| VSL142 | CHOKE ALL CARBS ADJ IN CARB | Choke, all, adjuster in carb top | £9.00 |
| VSL143 | SPEEDO CHRONOMETRIC S/ARM | Speedometer, chronometric, 5'-3" swing/arm | £15.27 |
| VSL144 | SPEEDO MAGNETIC S/ARM | Speedometer, magnetic, 5'-3" swing/arm | £10.50 |
| VSL145 | SPEEDO CHRONOMETRIC RIGIDS | Speedometer, chronometric 4'-8" rigids | £9.75 |
| VSL146 | SPEEDO CHRONO FRONT WHEEL | Speedometer, chronometric, front wheel, 2'-4", with spade drive | £14.25 |
| VSL147 | TACHO CHRONOMETRIC | Tachometer, chronometric, with spade drive | £14.25 |
| VSL148 | TACHO MAGNETIC | Tachometer, magnetic, with spade drive | £9.90 |
| GASKET SETS | |||
| VSL009 | GASKET SET IRON MAC/MOV | £12.50 | |
| VSL010 | ALLOY MAC GASKET SET | £11.20 | |
| VSL011 | KSS MK2 GASKET SET | £13.40 | |
| VSL012 | VM/MSS GASK SET | Includes reinforced rocker box gasket | £20.50 |
| VSL154 | VIPER GASKET SET | Includes reinforced rocker box gasket | £12.50 |
| VSL155 | THRUXTON GASKET SET | Includes reinforced rocker box gasket | £14.00 |
| VSL099 | GASKET PAPER 0.25MM X A4 | Cut your own unobtainable gaskets. | £0.75 |
| PANNIER SETS | |||
| VSL003 | PANNIER FRAME | Fits S/Arm models only. Priced per single side, please order L or R . See also pannier bags; VSL169 & 170 | £55.00 |
| VSL004 | CARRIER FOR 3.5G TANK | For use on bikes with 3 1/2 gallon tank and requires VSL003; unless you make your own support brackets | £37.00 |
| VSL005 | CARRIER FOR 4G TANK | For use on bikes with 4 1/4 gallon tank and requires VSL003; unless you make your own support brackets | £35.00 |
| VSL169 | PANNIER BAGS STD | priced per single bag | £35.00 |
| DYNAMO TOOTHED BELT DRIVE CONVERSIONS | |||
| A range of engine pulleys, dynamo pulleys and belts which can be mixed and matched to | |||
| suit MOV, MAC, All MSS, VR, VM, VMT & KSS MkII and provide two dynamo speed options | |||
| for any of these models. | |||
| YOU NEED TO TELL US WHICH MODEL you want to fit the conversion to and whether | |||
| you want the dynamo to run at 1.1 x engine speed or 1.25 x engine speed. | |||
| Originally, MSS after engine number 12914, VR after 3605 and VM after 5049 probably had | |||
| larger dynamo pulleys (60w dynamo and longer belt E16/4) to give a slower dynamo speed. | |||
| Otherwise 36w dynamos can be run faster. | |||
| Items can be ordered separately, but for kits just tell us your Model and Speed choice | |||
| VSL380 | ENG PULLEY 40T VM/MSS/VR/VMT | All MSS/KSS/VM/VR | £29.50 |
| VSL381 | ENG PULLEY 40T MOV\MAC | MAC/MOV | £28.50 |
| VSL382 | DYNO PULLEY 32T | For faster dynamo speed option | £22.50 |
| VSL383 | DYNO PULLEY 36T | For slower dynamo speed option | £26.00 |
| VSL384 | TOOTHED BELT 90T | For VSL381 + VSL382 | £9.00 |
| VSL385 | TOOTHED BELT 95T | For VSL381 + VSL383 OR VSL380 + VSL382 | £10.50 |
| VSL386 | TOOTHED BELT 100T | For VSL380 + VSL383 | £12.00 |
| VSL388 | DYNO PULLEY 36T FOR 13 MM SHAFT | Keywayed shaft for Alton alternator and Lucas Dynamo | £26.00 |
| FLEXIBLE PIPE & FITTINGS | |||
| VSL396 | OIL PIPE 3/8 INCH BORE - RUBBER | Black rubber (with specification printed along length), proper fuel/oil resistant with thick reinforced walls- 11/16 inch O.D., priced per yard | £4.50 |
| VSL397 | OIL PIPE 5/16 INCH BORE - PLASTIC | Clear PVC with braided reinforcement, 9/16 inch O.D., priced per yard - Hoping to reorder soon | £1.00 |
| VSL398 | OIL PIPE 3/8 INCH BORE - PLASTIC | Clear PVC with braided reinforcement, 5/8 inch O.D., priced per yard | £1.45 |
| VSL399 | OIL PIPE 5/16 INCH BORE - RUBBER | Black rubber (with specification printed along length), reinforced, proper fuel/oil resistant, 19/32 inch O.D., priced per yard | £3.00 |
| VSL400 | PET.PIPE 1/4 INCH BORE - PLASTIC | Clear PVC with braided reinforcement, 15/32 inch O.D., priced per yard - Hoping to reorder soon | £1.00 |
| VSL409 | SPIGOT ELBOW 1/4 BSP | For petrol tap below, includes nut | £2.95 |
| FASTENERS | |||
| VSL023 | 4 IN PLASTIC CABLE TIE | £0.02 | |
| VSL079 | 5 1/2 IN PLASTIC TIE | £0.03 | |
| VSL080 | 12" PLASTIC CABLE TIE | £0.08 | |
| VSL024 | 15 IN PLASTIC CABLE TIE | £0.12 | |
| VSL315 | 2BA X 1/2 LONG HEX HEAD SCREW | Stainless | £0.71 |
| VSL300 | 1/4 BSF X 3/8 HEX SCREW PLATED | Plated | £0.20 |
| VSL316 | 1/4" BSF X 1/2" LONG HEX SCREW | Stainless | £0.50 |
| VSL300A | 1/4 BSF X 5/8 HEX SCREW PLATED | Plated | £0.20 |
| VSL316A | 1/4BSF X 3/4 LONG HEX SCREW | Stainless - use as SL8/5 | £0.65 |
| VSL316B | 1/4 BSF X 1 HEX BOLT | Stainless | £0.85 |
| VSL301 | 1/4 BSF X 1 1/8 HEX BOLT PL | Plated | £0.25 |
| VSL317 | 1/4" BSF X 1 1/4" HEX BOLT | Stainless | £0.85 |
| VSL301A | 1/4" BSF X 1 1/2" HEX BOLT | Plated | £0.25 |
| VSL318 | 1/4" BSF X 1 1/2" HEX BOLT | Stainless | £0.85 |
| VSL319 | 1/4" BSF X 1 3/4" HEX BOLT | Stainless | £0.60 |
| VSL316W | 1/4 BSW X 1/2 SCREW | Stainless - use as SL8/22 - Hoping to reorder soon | £0.30 |
| VSL322A | 1/4 BSW X 1 HEX SCREW | Stainless - use as SL8/16 | £0.80 |
| VSL322B | 1/4 BSW X 1 1/4 HEX BOLT | Stainless - use as SL8/17 | £0.90 |
| VSL322C | 1/4 BSW X 1 3/4 HEX BOLT | Stainless - use as SL8/21 | £1.10 |
| VSL321 | 5/16" BSF X 3/4" HEX SCREW | Stainless | £1.35 |
| VSL302 | 5/16" BSF X 7/8" HEX BOLTS | Plated | £0.30 |
| VSL302A | 5/16" BSF X 1 1/4" HEX SCREW | Plated - Hoping to reorder soon | £0.30 |
| VSL302B | 5/16 BSF X 1 1/4 HEX SCREW | Stainless - use as SL109/10 | £1.50 |
| VSL320 | 5/16" BSF X 1 1/2" HEX BOLT | Stainless - use as SL9/22 | £1.40 |
| VSL324 | 5/16 BSF X 1 5/8 HEX BOLT | Stainless - use as SL109/11 | £1.95 |
| VSL325 | 5/16 BSF X 2 HEX BOLT | Stainless - use as SL109/6 | £1.85 |
| VSL326 | 5/16 BSF X 2 3/4 HEX BOLT | Stainless - use as SL9/18 | £2.40 |
| VSL327 | 5/16" BSF X 3" HEX BOLT | Stainless - use as SL109/15 | £2.45 |
| VSL304 | 3/8" BSF X 1 1/4" BOLT | Plated | £0.40 |
| VSL328 | 3/8 BSF X 1 1/4 HEX SCREW | Stainless - use as SL110/2 | £1.70 |
| VSL329 | 3/8 BSF X 1 3/4 HEX BOLT | Stainless - use as SL110/3 | £2.25 |
| VSL329A | 3/8 BSF X 2 HEX BOLT | Stainless - use as SL110/4 and SL110/8 | £2.10 |
| VSL331 | 2BA NYLOC NUT | £0.45 | |
| VSL332 | 2BA NUT | Stainless | £0.17 |
| VSL332B | 2BA NUT BRASS | Brass | £0.20 |
| VSL330 | 3/16 WHIT NUT. PLATED. | Plated - for rear light units | £0.05 |
| VSL333 | 1/4" BSF NUT | Stainless | £0.20 |
| VSL334 | 1/4" BSF NYLOC NUT | Stainless | £0.80 |
| VSL335 | 5/16" BSF NUT | Stainless | £0.30 |
| VSL336 | 5/16" BSF NYLOC NUT | Stainless | £1.05 |
| VSL337 | 5/16 CYCLE THREAD NUT | Stainless - use as SL56/5 | £0.95 |
| VSL338 | 3/8" BSF NUT | Stainless | £0.35 |
| VSL339 | 3/8 BSF NYLOC NUT SS | Stainless | £1.25 |
| VSL339/B | 3/8 BSF NYLOC NUT | Blackened H-T Steel - Hoping to reorder soon | £1.00 |
| VSL340 | 3/8 CYCLE THREAD NUT | Stainless - use as SL56/8 - Hoping to reorder soon | £0.75 |
| VSL340/B | 3/8 CYCLE THREAD NUT | Blackened H-T Steel | £0.60 |
| VSL341 | 7/16" BSF NUT | Stainless | £1.25 |
| VSL341A | 7/16 BSF NYLOC NUT | Stainless | £1.10 |
| VSL343 | 2BA PLAIN WASHER | Stainless | £0.09 |
| VSL343K | 3/16 SHAKEPROOF WASHER | Stainless | £0.09 |
| VSL354 | 3/16 PLAIN WASHER PLATED | Plated | £0.03 |
| VSL355 | 3/16 SHAKEPROOF WASHER | Plated | £0.03 |
| VSL344 | 1/4 PLAIN WASHER | Stainless | £0.05 |
| VSL353 | 1/4 SHAKEPROOF WASHER | Plated | £0.05 |
| VSL344K | 1/4 SHAKEPROOF WASHER | Stainless | £0.09 |
| VSL344L | 1/4 SINGLE COIL LOCK WASHER | Stainless | £0.09 |
| VSL344P | 1/4" X 1" O/D WASHER | Plated Mild Steel | £0.06 |
| VSL345 | 5/16" PLAIN WASHER | Stainless | £0.15 |
| VSL309 | 5/16" SHAKEPROOF WASHER | Plated | £0.07 |
| VSL345K | 5/16 SHAKEPROOF WASHER | Stainless | £0.02 |
| VSL345L | 5/16 SINGLE COIL LOCK WASHER | Stainless | £0.12 |
| VSL310 | 3/8 FLAT WASHER PLATED | Plated | £0.08 |
| VSL346 | 3/8 PLAIN WASHER | Stainless | £0.10 |
| VSL346K | 3/8 SHAKEPROOF WASHER | Stainless | £0.15 |
| VSL346L | 3/8 SINGLE COIL LOCKWASHER | Stainless | £0.20 |
| VSL347 | 7/16" PLAIN WASHER | Stainless | £0.15 |
| VSL347K | 7/16 SHAKEPROOF WASHER | Stainless | £0.25 |
| VSL347L | 7/16 SINGLE COIL LOCKWASHER | Stainless | £0.25 |
| VARIOUS | |||
| When ordering items such as fork spindles or nuts, it is well worth sending us a sample | |||
| VSL007 | PETROL TANK CAP | £9.30 | |
| VSL008 | OIL TANK CAP VENTED | £7.15 | |
| VSL008A | OIL TANK CAP NON VENTED | £8.25 | |
| VSL013 | REAR WHEEL DUST COV 3 HOLE | Hub must be bare (no spokes) to fit - Hoping to reorder soon | £9.80 |
| VSL014 | SPACER TUBE FOR VSL 013 | £2.40 | |
| VSL015 | RUBBER PLUG FOR VSL013 | Prevent loss of wheel nuts and thence damage to speedo drive gearbox - very tight fit - priced each, so order 3 (price reflects tooling cost) - Hoping to reorder soon | £3.10 |
| VSL019 | PAPER OIL FILTER KIT COMP | Complete with element, fits all S/Arm models with no external modifications. See illustration on back cover | £25.50 |
| VSL020 | PAPER OIL FILTER ELEMENT | £6.50 | |
| VSL032 | SPEEDO BEZEL NACELLE TYPE | Chrome plated - Hoping to reorder soon | £12.70 |
| VSL036 | F/MUDGUARD MOV/MAC/KTS/RIG MSS | Replica of KA 16/5 in strong fibreglass. Not sent by mail (except at your risk) | £46.00 |
| VSL039 | REAR MUDGUARD TAILPIECE F/G | MAC/MSS S/Arm equivalent to MAS85, in fibreglass for use with VSL041. Not sent by mail (except at your risk). | £12.00 |
| VSL041 | R/MUDGUARD MAC/MSS S/ARM F/G | Equivalent to A15/19 in fibreglass, use tailpiece VSL039. Not sent by mail (except at your risk). | £38.50 |
| VSL044 | BRKT FOR REAR F/G M/GUARD | £4.90 | |
| VSL052 | DAMPER NUTS | Send us a drawing in case we can match what you need | £4.90 |
| VSL054 | UNKNOWN FORK SPINDLES | Send us a drawing in case we can match what you need | £5.00 |
| VSL094 | BRASS CAGE LESS ROLLERS | Replaces MAS57, requires 14 of rollers VSL095 | £7.25 |
| VSL095 | 3/16 X 3/16 ROLLERS | For use in VSL094 | £0.16 |
| VSL098 | LUGS FOR PR. CH/CASE BAND | Bare casting, priced in units of one | £2.30 |
| VSL103 | EXCHANGE BRAKE SHOES | Only available at Huncote counter, not by mail order - your old shoes must be a pair, in good condition and with undamaged bearing surfaces. | £24.00 |
| VSL106 | VEELINE FAIRING BRACKET L/H | Left-hand side onto footrest | £3.45 |
| VSL107 | 5/8 X 3/8 1 1/2 LINK | Two links, one with cranked plates to give 'two inners' | £2.65 |
| VSL108 | 5/8 X 3/8 JOINING LINK | £1.95 | |
| VSL110 | 1/2 X 5/16 1 1/2 LINK | Two links, one with cranked plates to give 'two inners' | £2.40 |
| VSL111 | 1/2 X 5/16 JOINING LINK | £1.80 | |
| VSL116 | MAIN SADDLE SPRINGS PAIR | For rigid models - Hoping to reorder soon | £15.00 |
| VSL117 | FLEXIBLE MOUNTINGS | £0.30 | |
| VSL150 | CLUTCH FRICTION PLATE | See illustration on back cover | £10.00 |
| VSL151 | CLUTCH PLAIN PLATE | See illustration on back cover | £5.00 |
| VSL152 | CLUTCH CHAINWHEEL | For 9-plate clutches - See illustration on back cover | £108.00 |
| VSL153 | CLUTCH CHAINWHEEL | For 7 plate clutches. Uses VSL150 & VSL151 plates. | £108.00 |
| VSL157 | BRKT FOR FRT F/G M/GUARD | £3.50 | |
| VSL164 | BRG.TAPER ROLLER STRG.HD.TOP | i.e. Replaces LE532 + F32/3 + 19xK100 - S/Arm only | £17.50 |
| VSL165 | BRG.TAPER ROLLER STRG.HD.BOTTO | As VSL 164 but with centre ground out to correct diameter of lower stem and so replace F32/4 - S/Arm only | £31.50 |
| VSL171 | FRICT DISC BLANK 3.25 ROUND | £4.85 | |
| VSL359 | DRIFT FOR KS18/3 WHEEL BEARING | £6.00 | |
| VSL360 | DRIFT FOR W62/2 HOLLOW SPINDLE | £6.00 | |
| VSL361 | SUSPENSION SET LENGTH | For perfectionists to adjust rear chain on S/Arm models - Hoping to reorder soon | £4.00 |
| VSL363 | EE9 BALL RACE | 3/8" wide - a pair might be a possible substitute for M87 - no guarantee! | £5.00 |
| VSL364 | GLAND NUT SPANNER | For OHC vert shaft housing nuts. | £15.00 |
| VSL365 | REAR HUB SHK ABS SPRING | Early 2-stroke models - priced per set of 8 | £15.00 |
| VSL368 | G.BOX SPKT 19T 1/2 X 3/16 | £10.00 | |
| VSL454 | EXHAUST PIPE CLAMP 2 INCH | Band and trunnion type, clamps 2" diameter | £8.00 |
| VSL457 | EXHAUST PIPE CLAMP 1.3/4 INCH | Band and trunnion type, clamps 1.75" diameter. | £8.00 |